|
NM-8AM做拨号服务器配置实例。
version 12.2
service timestamps debug
datetime msec
service timestamps log
uptime
no service
password-encryption
!
hostname cisco3640
!
boot system
flash:c3640-i-mz.122-8.T
enable secret 5
!
username abc password 0
abc
! -- Usernames for local
authentication of the
call.
! -- The client presents
the username/password
and the NAS
! -- authenticates the
peer. To use AAA with
RADIUS or TACACS+, refer
to
! -- Implementing the
Server-Based AAA
Subsystem.
ip subnet-zero
!
no ip domain-lookup
ip domain-name cisco.com
!
async-bootp dns-server
5.5.5.1 5.5.5.2
! -- Specifies (for
async clients) the IP
address of domain name
server.
!
!
interface Loopback0
ip address 1.1.1.1
255.255.255.0
!
interface Ethernet2/0
ip address 20.20.20.1
255.255.255.0
half-duplex
!
! <<--Unused interface
configuration omitted.
!
interface Group-Async1
! -- This group-async
interface is the
configuration template
for all modems.
! -- Individual async
interface do not have to
be configured since they
! -- can be cloned from
one managed copy.
ip unnumbered Loopback0
encapsulation ppp
dialer in-band
dialer idle-timeout 600
! -- Sets Idle timer to
600 seconds (10
minutes).
dialer-group 1
!--- Apply interesting
traffic definition from
dialer-list 1.
! -- Note: The specified
dialer-group number must
be the same as
! -- the dialer-list
number; in this example,
defined to be "1".
! -- Interesting traffic
specifies the packets
that should reset the
idle timer.
async mode interactive
! -- If the async
interface is to answer
different connection
types
! -- (exec,ppp,slip),
use this command in
conjunction with
autoselect ppp
! -- under the line
configuration to auto
detect the connection
type.
! -- To prevent users
from establishing an
"EXEC session" to the
router.
! -- use the command
async modem dedicated
instead.
peer default ip address
pool DIALIN
! -- Clients are
assigned addresses from
the ip address pool
named "DIALIN".
ppp authentication chap
group-range 1 8
! -- Modems/lines 1 to 8
are members of this
group async interface.
! -- If you want, for
example, only 4 modems
for incoming and the
rest
! -- for outgoing then
configure the group
range for any set of
! -- four consecutive
modems in the module.
! -- Note: this range
must be included within
the line configuration
below.
!
ip local pool DIALIN
10.1.1.1 10.1.1.10
! -- IP address pool for
dialin clients.
ip classless
ip route 0.0.0.0 0.0.0.0
20.20.20.100
ip http server
ip pim bidir-enable
!
!
dialer-list 1 protocol
ip permit
! -- Specifies all IP
traffic as interesting.
Interesting traffic
! -- specifies the
packets that should
reset the idle timer.
! -- This is applied to
interface Group-Async 1
using dialer-group 1.
! -- Note: The specified
dialer-list number must
be the same as the
! -- dialer-group
number; in this example,
defined to be "1".
!
line con 0
password abc
line 1 88
! -- TTY lines for the
NM-8AM Modems.
! -- Note the line
number range matched the
group-range
! -- under the group-async
config.
modem InOut
! -- Support incoming
and outgoing modem
calls.
transport input all
autoselect ppp
! -- Launch PPP if PPP
packets are detected.
This is used in
conjunction
! -- with async mode
interactive under the
group-async
configuration.
flowcontrol hardware
line aux 0
line vty 0 4
loginn
!
!
end |
